MasterTile WP 666 | Waterproofing for floors
Cement-acrylic two-component highly elastic waterproofing compound, for indoor waterproofing, with a tile finish
Terrace floor waterproofing
Bathroom floor waterproofing
Floor waterproofing in a private house
MasterTile WP 666 | Two-component elastic waterproofing, cement and acrylic based, for the protection of concrete and cement-based plasters.
-
It is used under the protection of tiles or screeds.
-
Complies with EN 1504-2, EN 14891.
-
Type CM = cementitious, liquid applied waterproofing material.
- Class O2P = resistant to water containing chlorides with crack-bridging effect, incl. at low temperatures.
Scope of waterproofing for all industries
-
On vertical and horizontal surfaces, indoors and outdoors.
-
Swimming pools, incl. Olympic.
-
Terraces.
-
Wet rooms (bathrooms, toilets, kitchens, balconies).
-
Walls of foundations and basements (protection against positive water pressure.
-
Wet rooms (baths, toilets, kitchens and balconies).
-
Water storage (subject to surface protection.
-
Saunas, baths, SPA zones.
- Exploited terraces and roofs.
Features and Benefits
-
Easy to use.
-
Apply both with a brush and by spraying.
-
Extended laying time.
-
Crack bonding due to high elasticity.
-
Forms a seamless, water-blocking finish.
-
Resistant to chemicals and salts contained in soils.
-
Vapor permeable.
-
High durability.
-
Resistant to freeze-thaw cycles.
-
Can be used in areas where vibration or movement is possible.
- It is an ideal durable and elastic base for laying ceramic tiles on it without additional processing and intermediate layers.
Scope of waterproofing for floors
-
Foundation waterproofing.
-
Floor waterproofing in a private house.
-
Floor waterproofing in the apartment.
-
Waterproofing the floor in the bathroom under the tiles.
-
Floor waterproofing before screed.
-
Waterproofing of basement walls (negative).
-
Waterproofing the floor in the garage.
- Floor waterproofing on an open balcony or terrace.
Specifications
|
MasterTile WP666 comp. BUT |
Mineral filler, polymer-modified additives, special cement
|
|
MasterTile WP666 comp. AT |
dispersion based on acrylic copolymer
|
|
Color |
Grey
|
|
Adhesion strength |
≥1.5N/mm2 (28d)
|
|
Resistant to positive water pressure |
7 bar (film 2mm)
|
|
Capillary water absorption (EN 12808-5) |
≤ 0.1 g (after 4 hours)
|
|
Application temperature |
+5°С +25°С
|
|
Operating temperature |
-20°С +80°С
|
|
Remix time |
3-5 minutes
|
|
Working hours |
2 hours
|
|
Period before operation |
2 days
|
|
Waterproof |
7 days
|
|
Period before topcoating (tiles, plaster) |
3 days |
Surface preparation
-
The substrate must be dry, free of defects, mostly even, clean and finely porous, free of pits, voids, cracks, dust, tar, bitumen, old paint and other factors that impair adhesion.
-
Wood and metal inclusions should be removed and active leaks should be repaired with MasterSeal 591 or other methods.
-
Cavities and sinks must be filled with mixtures from the MasterEmaco series.
-
At vertical and horizontal corners, roundings with a radius of at least 4 cm should be used.
-
The substrate must be thoroughly moistened before coating.
-
If the material, after being applied to the surface, begins to quickly lose water. This means that the surface is not sufficiently moistened.
-
For application in conditions of high temperature or in windy weather, it is possible to increase the dosage of water by 10%.
Mixing
-
Add liquid part B (MasterTile WP 666 part B) to a clean mixing container, slowly add part A (MasterTile WP 666 part A) and mix at low speed 400-600 rpm for 3-5 minutes until a homogeneous mixture is obtained .
-
Leave the mixture for 3-5 minutes to ripen, then stir again for 30 seconds.
-
After that, the mixture is ready for use.
-
MasterTile WP666 Part A: 20 kg.
- Part B: 10 kg.
- The density of the mixture is: 1.70kg/l.
Application
-
The prepared mortar is applied by Thoro Brush with a brush or spatula in 2 or 3 layers in perpendicular fusing one to the other.
-
The time interval between layers depends on the application conditions.
Consumption
-
1st layer - 1.2 kg / m2.
-
2nd layer - 1.0 kg/m2.
- 3rd layer - 1.0 kg/m2.
Important aspects when applying
-
The air temperature and the temperature of the base must be at least 5 ºС or not more than 25 ºС.
-
Do not use MasterTile WP 666 in the rain or if there is a chance of rain.
-
MasterTile WP 666 applied at +23°C gains mechanical strength after 2 days, becomes waterproof after 7 days and gains final strength after 14 days.
-
The coating must be protected from direct sunlight, wind, frost or rain for 24 hours.
-
The application time of systems based on cement and acrylic emulsions depends on the temperature and relative humidity of the air.
-
At low temperatures, the reaction slows down, which increases the working time and setting time.
-
High temperature speeds up the reaction and the times mentioned above are reduced.
-
In order for the material to harden, the temperatures of the material, substrate and air cannot be less than the minimum permitted temperatures.
-
Areas that are not yet fully cured should not come into contact with water.
-
The film thickness of each coating layer should not exceed 1.2mm.
-
Do not use MasterTile WP 666 as flooring in pedestrian areas.
-
The coating here must be protected with a screed (based on the modifying additive MasterCast 125 ) or ceramic tiles.
-
Apply, for laying tiles, materials from the MasterTile series.
Cleaning tools
-
Clean tools and equipment with warm soapy water after use.
- Once MasterTile WP 666 has hardened, it can be mechanically removed from the surface.
Package
-
Set weighing 30kg.
-
Part A - 20kg bag.
- Part B - canister 10kg.
Storage
-
Store in original, unopened packaging in cool, dry conditions, protected from frost.
-
For short-term storage, a maximum of 3 pallets can be stacked one on top of the other.
-
For long-term storage, pallets cannot be stacked one on top of the other.
Best before date
-
MasterTile WP 666 has a 12 month warranty in unopened, undamaged packaging.
-
Part B of MasterTile WP 666 freezes at 0°C and below.
-
Store bags only on pallets covered with stretch film in a dry place.
-
Protect from direct sunlight and rain.
-
Failure to comply with the recommended storage conditions may result in damage to the material or packaging.
-
Opened packages must be tightly closed immediately and used within one week after opening.
Security measures
-
Do not approach storage facilities during a fire;
-
Store products in well-ventilated areas;
-
During work, work clothes, protective gloves, goggles and a mask should be used in accordance with health and safety regulations;
-
Since uncured materials have an irritating effect, contact of the components with the skin and eyes should not be allowed, and in case of contact, rinse with plenty of water;
-
If swallowed, seek medical attention immediately;
-
It is forbidden to bring food and drink to the construction site where the product is used;
-
The product must be kept out of the reach of children.
