LITOLIV EXPRESS | Leveling mixture for the floor
Self-leveling mixture for 3-40 mm chaff, reinforced with fiber
Floor leveling
Leveling mixture for tiles
A leveler with a quick build-up of strength
COMPLETE SUPPLY
complete project package
HIGH QUALITY
goods from the world's leading manufacturers
ADVANTAGES
- Excellent ability to self-align;
-
Easy application;
-
High bending and compressive strength after only 4 hours;
-
Quick drying;
-
Absence of shrinkage during drying;
- Very low release of volatile organic compounds.
FIELD OF APPLICATION
It is intended for leveling internal, horizontal bases, with a layer of 3 to 40 mm, in residential buildings and commercial premises (offices, stores), where intensive surface loads are not provided.
Recommended bases:
-
cement screeds made by Litocem or Litocem Pronto;
-
warm floors (electric and water);
-
anhydrite (gypsum) screeds;
-
existing coatings made of ceramics, natural stone or marble chips;
- concrete slabs.
Appearance |
Powder
|
Color |
Grey
|
Ripening time |
3 minutes
|
Consistency |
Liquid
|
Lifetime of the product |
About 30 minutes at a temperature of +23 °C
|
Application temperature |
From +5°C to +35°C
|
Layer thickness |
From 3 to 40 mm in one application
|
The beginning of walking |
After 3 hours at a temperature of +23 °C
|
Dwelling time before facing |
24 hours
|
Consumption |
1.6 kg/m2 for every mm of thickness
|
Mechanical resistance to compression after 28 days |
≥ 15 N/mm2 |
Mechanical resistance to bending after 28 days |
≥ 5 N/mm2 |
Adhesion with concrete after 28 days |
≥ 1 N/mm2
|
Bag |
20
|
FOUNDATIONS
-
The bases must be clean, dry, strong, dense, sufficiently durable, without removable parts and protected from rising moisture;
- Any cracks or chips must be repaired: moisten the surface with Decor Primer Fondo primer and immediately sprinkle with dry sand or quartz with a particle size of 0.4 to 1 mm.
Preparation is based
-
Porous, highly absorbent and dusty bases must be pre-treated with Primer C, which closes the pores of the base and promotes better spreading and self-leveling of the product;
-
Dense and smooth surfaces (concrete, old ceramic tiles, marble chips) should first be degreased with a 10% solution of caustic soda or alkaline detergents, and then treated with the Prepara Fondo primer;
-
Anhydrite, gypsum screeds must be pre-polished and primed with Primer C or Primer X94;
-
It is necessary to measure the maximum moisture content with a carbide hygrometer, the indicator should not exceed 0.5%.
COMPENSATION SEAMS
- It is necessary to provide compensatory seams to divide the continuity of the lined surface;
-
As a rule, they should be performed in rooms with an area of 50 m2 or 25-30 m2, in the case of a warm floor;
-
In rooms with an area of less than 50 m2, it is possible to perform a seam only at the door joints.
PREPARATION OF THE SOLUTION
- Dilution ratio: 4.4 - 4.8 liters (22-24%) of water per 20 kg (1 bag) Litoliv Express;
- To obtain a solution, you should slowly pour the powder into water with constant stirring at low speeds, using an electric drill with a mixer nozzle to obtain a homogeneous, lump-free solution.
-
Attention! Keep the resulting solution for 3 minutes;
-
After re-mixing, the solution is ready for use.
-
The life time of the finished solution is about 30 minutes, so it is recommended to mix the amount of material that will be used in this period of time;
-
If the composition is applied with a plaster pump from a construction mixer, then the amount of water should be the same as with manual preparation.
APPLICATION
-
The solution is poured directly onto the base and distributed over the surface with a smooth spatula or squeegee, forming a layer of the required thickness;
-
It is recommended to roll the surface of the solution with a needle roller for better spreading and removal of air bubbles.
- The solution can also be applied by machine.
LAYING TILE
-
The subsequent installation of tiles, stone, parquet, soft and woven floor coverings can be started after 24 hours;
- When laying the parquet, the thickness of the Litoliv Express layer should be at least 3 mm.
Recommended glue
-
For laying ceramic tiles, porcelain stoneware, clinker and cotto: cement adhesive mixtures of class C2 – C2F;
- For natural and artificial stone: Litostone K99, Litoflott K88, Litoelastic.
Compatible waterproofing materials:
Waterproofing can be performed with Elastocem, Coverflex or Hidroflex materials, which are applied 24 hours after pouring Litoliv Express and 24 hours before laying the ceramic material.
ATTENTION
-
Do not add lime or cement to the product;
-
Does not apply to bases exposed to the effect of rising moisture;
-
Apply at temperatures from +5 to +35 °C;
-
Observe the specified amount of water for preparing the solution;
-
An excess of water can lead to an increase in the setting time, the possible formation of cracks, chips or a loose surface;
-
In a hot climate, store the package in a cool place, protected from the sun;
-
Pretreatment of the Primer C surface improves the adhesion of the leveling layer and facilitates the application of the product due to the uniform absorption of the base;
- Do not use the product for purposes not specified in this technical description.