CEMTOP 350 | Self-leveling industrial floors
Top coat, for industrial floors, cement-based, for intensive use, 6-30 mm
Industrial floors for a warehouse
Industrial garage flooring
Industrial floors
CEMTOP 350 | Self-levelling floor product, ready for diffusion, characterized by very little shrinkage during curing, which can be applied with a mortar pump.
-
CEMTOP 350 is based on aluminous cement, aggregates, additional binders and polymer.
- CEMTOP 350 is a ready to use dry powder ready to be mixed with water before use.
METHODS AND APPLICATIONS
-
CEMTOP 350 is designed for use in industrial buildings such as warehouses, warehouses, offices and areas where there is heavy forklift traffic;
-
It is characterized by excellent adhesion to the base and is resistant to water;
-
It can be used as a subfloor for carpet and floor tiles;
-
CEMTOP 350 can be applied with an automatic continuous concrete mixer with a pump (without mortar hopper);
-
The recommended thickness is: 6-10 mm during one operation;
-
The maximum thickness is 30mm;
-
Under normal conditions, you can walk on it after 1-2 hours, and after one week, depending on the conditions of the object, subject it to heavy loads;
- Dry and freshly laid, the product can be painted with CEMPUR varnish or paint to protect it from dirt that penetrates the cement screed.
- Substrate preparation for laminate, parquet, linoleum, ceramic tiles, rubber tiles.
Scope of application
-
Industrial floors for the garage.
-
Industrial floors for a warehouse.
-
Self-leveling industrial floors for commercial premises.
- Self-leveling industrial floors for industrial premises.
Specifications
|
Bending strength |
11 N/mm² after 28 days
|
|
Compressive strength |
40 N/mm² after 28 days, ultimate strength >45 N/mm2
|
|
Black floor grip |
> 3 N/mm²
|
|
VOC content |
Without ammonia and formic aldehydes
|
|
Particle size |
Max. 1 mm
|
|
Natural shrinkage |
< 0.5 ‰, measured relative humidity 55%
|
|
PH level |
About 11.5
|
|
Mobility |
150-155 mm
|
|
Water resistance |
Waterproof (expansion under water < natural shrinkage)
|
|
Material consumption |
1.75 kg / mm / m²
|
|
Mixing with water |
18% (4.5 liters / 25 kg of product)
|
|
Penetrometer Mobility Measurements |
150-155mm
|
|
Minimum applied temperature |
+6C
|
Base
-
CEMTOP 350 must be applied to a well finished subfloor;
-
The surface strength of the base must not be higher than 1.5 N/mm²;
-
Remove dust, laitance, grease or other materials;
-
The material has very good fluidity, providing a smooth surface for carpeting;
-
To cover inclined planes, it is recommended to use a small amount of water and pour from the highest point to the lowest;
-
Incompletely set material can be easily processed or removed, allowing the necessary leveling to be achieved.
MIXTURE PRODUCTION
-
CEMTOP 350 can be mixed in an automatic continuous concrete mixer with a pump (no mortar hopper);
-
To do this, you need to use clean drinking water in the proportion of 4.5 liters per bag weighing 25 kg;
- Mixed material must be used within 15 minutes.
APPLICATION
-
Door sills, steps, gutters and storm drains must be insulated with a foam barrier;
-
Large surfaces should be divided into sections;
-
Typical plot width: 8-12 m, depending on pump power.
CLEANING
All tools and equipment should be cleaned with water immediately.
HEALTH & SAFETY
-
Danger - contains cement, wet cement is corrosive;
-
Protect eyes and avoid prolonged skin contact;
-
Keep out of the reach of children.
