VIMAPUR VARNISH | Polyurethane floors

Two-component finishing polyurethane varnish for floors

Description

Characteristics

Application

VIMAPUR VARNISH - transparent, two-component, solvent-based polyurethane varnish.

It is used as a final protective coating of the surfaces of concrete and cement structures, stone, decorative brick, wood, metal and polyester.
It contains substances that protect against the effects of ultraviolet rays, which provide the surface with long-term resistance to solar radiation;
VIMAPUR VARNISH preserves the gloss of the coated material and prevents it from yellowing over time.
And it also preserves the matte appearance of the surface, where shine is undesirable;
The material has excellent adhesion, even in cases of glossy surfaces, such as galvanized metal sheets;
Consumption - 0.12 - 0.16 kg / m2 per one layer.

To protect surfaces near the sea;
To protect and increase the durability of epoxy paints and floor coverings, as well as for pool surfaces;
For sealing the surfaces of terraces covered with tiles and mosaics, without changing their aesthetic appearance;
As a protective coating, for surfaces ironed with cement.

Technical characteristics
Density	Components A + B: 1.0 kg / l
Density (gloss 60o)	90 for a glossy surface 30 for a matte surface
Ratio of components (A: B)	2.57: 1 for a glossy surface 2.71: 1.30 for the appearance of a matte surface
It is used at ambient temperature	12 C -35 C
Workability time of finished varnish (A+c)	2.5 hours at + 12 C 2 hours at + 25 C 1 hour at + 30 C
The time of grasping	3 hours at + 25 C
Time to re-apply varnish	36 hours at + 12 C 24 hours at + 25 C
Time to walk on the surface	36 hours at + 12 C 24 hours at + 25 C
Absolute readiness of the surface	7 days at + 25 C

The base must be solid, without dust, grease and pollutants that prevent the adhesion of the material;
An important factor affecting the polymerization process is the humidity of the base (≤4%) and the humidity of the environment (≤ 65%);
In the case of impregnation of the base, it must dry before varnish is applied to obtain the desired result;
Attention! If siloxane impregnation was applied to the surface of the base, then VIMAPUR VARNISH should not be applied.

To protect the steel surface with VIMAPUR VARNISH varnish, it should be primed with water-based polyurethane primer VIMAPUR PRIMER-W.
In this case, the varnish should be applied after the final drying of the primer, not less than 24 hours;
If the base has a high absorbent capacity, then the surface should be primed with VIMAPUR VARNISH, having previously diluted it with a special THINNER-PU solvent in an amount of up to 15%.

The two components are emptied into a clean container and mixed for at least 3 minutes.
Then the mixture settles for ~ 5 minutes to initiate the reaction of the two components;
Next, the ready-to-use varnish is applied to the surface with a brush or roller, at least in two layers;
Consumption 0.12 - 0.16 kg / m2 per one layer.

Tools are cleaned with THINNER-PU solvent immediately after use.

Component A: 2 years, if the material is stored in factory sealed packaging, in a room protected from frost, moisture and high temperatures (> 350 C);
Component B: 6 months, if the material is tightly sealed in the factory packaging.
The material easily polymerizes under the influence of moisture.

VIMAPUR VARNISH-W after drying is safe for health;
Before using it, it is necessary to carefully read the contents of the safety instructions on the packaging.